NOTE: click here if you get an empty page.


E2FSCK(8)							     E2FSCK(8)

NAME

e2fsck - check a Linux ext2/ext3 file system

SYNOPSIS

e2fsck [ -pacnyrdfkvstDFSV ] [ -b superblock ] [ -B blocksize ] [ -l|-L bad_blocks_file ] [ -C fd ] [ -j external-journal ] [ -E extended_options ] device

DESCRIPTION

e2fsck is used to check a Linux second extended file system (ext2fs). E2fsck also supports ext2 filesystems containing a journal, which are also sometimes known as ext3 filesystems, by first applying the journal to the filesystem before continuing with normal e2fsck processing. After the journal has been applied, a filesystem will normally be marked as clean. Hence, for ext3 filesystems, e2fsck will normally run the journal and exit, unless its superblock indicates that further checking is required. device is the device file where the filesystem is stored (e.g. /dev/hdc1). Note that in general it is not safe to run e2fsck on mounted filesys- tems. The only exception is if the -n option is specified, and -c, -l, or -L options are not specified. However, even if it is safe to do so, the results printed by e2fsck are not valid if the filesystem is mounted. If e2fsck asks whether or not you should check a filesystem which is mounted, the only correct answer is ''no''. Only experts who really know what they are doing should consider answering this question in any other way.

OPTIONS

-a This option does the same thing as the -p option. It is pro- vided for backwards compatibility only; it is suggested that people use -p option whenever possible. -b superblock Instead of using the normal superblock, use an alternative superblock specified by superblock. This option is normally used when the primary superblock has been corrupted. The loca- tion of the backup superblock is dependent on the filesystem's blocksize. For filesystems with 1k blocksizes, a backup superblock can be found at block 8193; for filesystems with 2k blocksizes, at block 16384; and for 4k blocksizes, at block 32768. Additional backup superblocks can be determined by using the mke2fs program using the -n option to print out where the superblocks were created. The -b option to mke2fs, which spec- ifies blocksize of the filesystem must be specified in order for the superblock locations that are printed out to be accurate. If an alternative superblock is specified and the filesystem is not opened read-only, e2fsck will make sure that the primary superblock is updated appropriately upon completion of the filesystem check. -B blocksize Normally, e2fsck will search for the superblock at various dif- ferent block sizes in an attempt to find the appropriate block size. This search can be fooled in some cases. This option forces e2fsck to only try locating the superblock at a particu- lar blocksize. If the superblock is not found, e2fsck will terminate with a fatal error. -c This option causes e2fsck to use badblocks(8) program to do a read-only scan of the device in order to find any bad blocks. If any bad blocks are found, they are added to the bad block inode to prevent them from being allocated to a file or direc- tory. If this option is specified twice, then the bad block scan will be done using a non-destructive read-write test. -C fd This option causes e2fsck to write completion information to the specified file descriptor so that the progress of the filesystem check can be monitored. This option is typically used by pro- grams which are running e2fsck. If the file descriptor speci- fied is 0, e2fsck will print a completion bar as it goes about its business. This requires that e2fsck is running on a video console or terminal. -d Print debugging output (useless unless you are debugging e2fsck). -D Optimize directories in filesystem. This option causes e2fsck to try to optimize all directories, either by reindexing them if the filesystem supports directory indexing, or by sorting and compressing directories for smaller directories, or for filesys- tems using traditional linear directories. -E extended_options Set e2fsck extended options. Extended options are comma sepa- rated, and may take an argument using the equals ('=') sign. The following options are supported: ea_ver=extended_attribute_version Assume the format of the extended attribute blocks in the filesystem is the specified version number. The version number may be 1 or 2. The default extended attribute version format is 2. -f Force checking even if the file system seems clean. -F Flush the filesystem device's buffer caches before beginning. Only really useful for doing e2fsck time trials. -j external-journal Set the pathname where the external-journal for this filesystem can be found. -k When combined with the -c option, any existing bad blocks in the bad blocks list are preserved, and any new bad blocks found by running badblocks(8) will be added to the existing bad blocks list. -l filename Add the block numbers listed in the file specified by filename to the list of bad blocks. The format of this file is the same as the one generated by the badblocks(8) program. Note that the block numbers are based on the blocksize of the filesystem. Hence, badblocks(8) must be given the blocksize of the filesys- tem in order to obtain correct results. As a result, it is much simpler and safer to use the -c option to e2fsck, since it will assure that the correct parameters are passed to the badblocks program. -L filename Set the bad blocks list to be the list of blocks specified by filename. (This option is the same as the -l option, except the bad blocks list is cleared before the blocks listed in the file are added to the bad blocks list.) -n Open the filesystem read-only, and assume an answer of 'no' to all questions. Allows e2fsck to be used non-interactively. (Note: if the -c, -l, or -L options are specified in addition to the -n option, then the filesystem will be opened read-write, to permit the bad-blocks list to be updated. However, no other changes will be made to the filesystem.) This option may not be specified at the same time as the -p or -y options. -p Automatically repair ("preen") the file system. This option will case e2fsck to automatically fix any filesystem problems that can be safely fixed without human intervention. If e2fsck discovers a problem which may require the system administrator to take additional corrective action, e2fsck will print a description of the problem and then exit with the value 4 logi- cally or'ed into the exit code. (See the EXIT CODE section.) This option is normally used by the system's boot scripts. It may not be specified at the same time as the -n or -y options. -r This option does nothing at all; it is provided only for back- wards compatibility. -s This option will byte-swap the filesystem so that it is using the normalized, standard byte-order (which is i386 or little endian). If the filesystem is already in the standard byte- order, e2fsck will take no action. -S This option will byte-swap the filesystem, regardless of its current byte-order. -t Print timing statistics for e2fsck. If this option is used twice, additional timing statistics are printed on a pass by pass basis. -v Verbose mode. -V Print version information and exit. -y Assume an answer of 'yes' to all questions; allows e2fsck to be used non-interactively. This option may not be specified at the same time as the -n or -p options.

EXIT CODE

The exit code returned by e2fsck is the sum of the following condi- tions: 0 - No errors 1 - File system errors corrected 2 - File system errors corrected, system should be rebooted 4 - File system errors left uncorrected 8 - Operational error 16 - Usage or syntax error 32 - E2fsck canceled by user request 128 - Shared library error

SIGNALS

The following signals have the following effect when sent to e2fsck. SIGUSR1 This signal causes e2fsck to start displaying a completion bar. (See discussion of the -C option.) SIGUSR2 This signal causes e2fsck to stop displaying a completion bar.

REPORTING BUGS

Almost any piece of software will have bugs. If you manage to find a filesystem which causes e2fsck to crash, or which e2fsck is unable to repair, please report it to the author. Please include as much information as possible in your bug report. Ideally, include a complete transcript of the e2fsck run, so I can see exactly what error messages are displayed. (Make sure the messages printed by e2fsck are in English; if your system has been configured so that e2fsck's messages have been translated into another language, please set the the LC_ALL environment variable to C so that the tran- script of e2fsck's output will be useful to me.) If you have a writable filesystem where the transcript can be stored, the script(1) program is a handy way to save the output of e2fsck to a file. It is also useful to send the output of dumpe2fs(8). If a specific inode or inodes seems to be giving e2fsck trouble, try running the debugfs(8) command and send the output of the stat(1u) command run on the relevant inode(s). If the inode is a directory, the debugfs dump command will allow you to extract the contents of the directory inode, which can sent to me after being first run through uuencode(1). The most useful data you can send to help reproduce the bug is a compressed raw image dump of the filesystem, generated using e2image(8). See the e2image(8) man page for more details. Always include the full version string which e2fsck displays when it is run, so I know which version you are running.

AUTHOR

This version of e2fsck was written by Theodore Ts'o <tytso@mit.edu>.

SEE ALSO

badblocks(8), dumpe2fs(8), debugfs(8), e2image(8), mke2fs(8), tune2fs(8) E2fsprogs version 1.39 May 2006 E2FSCK(8)

1994 Man-cgi 1.15, Panagiotis Christias <christia@theseas.ntua.gr>